Our Products

We offer an incredibly diverse product selection.

Home / Products / Building Wire Copper / NMD90

NMD90

NMD90-Copper - NMD90

Two or three annealed (soft) copper conductors, with 90°C XLPE (T90) insulation.

Bare bonding wire and overall jacket of moisture resistant and flame retardant PVC, with FT1 rating.

  • CSA Spec C22.2 No. 48-M90 (R2005)
  • Rated 300 volts.

Minimum recommended handling temperature: minus 25°C for 2 conductor cables and minus 10°C for 3 conductor cables (with suitable handling procedures).
Maximum conductor temperature: 90°C.

Click to view spec sheet: NMD90
ECS Catalogue Number Conductor APPROX. O.D. APPROX. WEIGHT AMPS COLOUR PUT-UPS (Length)
AWG OR MCM NO. STRANDING (mm) (inches) (kgs/km) (lbs/1000ft)
NMD14-02
 14 2 1 9.86 x 4.88 0.388 x 0.192 101 68 15 PLEASE CALL 75, 150, 300
NMD14-03
 14 3 1 8.77 0.345 129 87 15 PLEASE CALL 75M, 150M, 300M
NMD12-02
 12 2 1 10.71 x 5.30 0.422 x 0.209 123 87 20 PLEASE CALL 75M, 150M, 300M
NMD12-03
 12 3 1 9.69 0.381 170 114 20 PLEASE CALL 75M, 150M, 300M
NMD10-02
 10 2 1 12.21 x 5.84 0.481 x 0.230 182 122 30 PLEASE CALL 75M, 150M, 300M
NMD10-03
 10 3 1 10.85 0.427 243 163 30 PLEASE CALL 75M, 150M, 300M
NMD08-02
 8 2 1 16.15 x 7.92 0.636 x 0.312 311 209 45 PLEASE CALL 75M, 150M, 300M
NMD08-03
 8 3 7 14.47 0.570 410 275 45 PLEASE CALL 75M, 150M, 300M
NMD06-02
 6 2 7 20.12 x 9.40 0.792 x 0.370 469 315 65 PLEASE CALL 75M, 150M, 300M
NMD06-03
 6 3 7 17.65 0.695 629 423 65 PLEASE CALL 75M, 150M, 300M

For open or concealed wiring in dry or damp locations where not exposed to mechanical injury.
Approved for use with ceiling fixtures

Available Jacket Colours:

  • #14 awg - White 2 & 3C #14 for General Application
  • Blue 2C#14 for Bedroom Outlets terminating at Arc Fault Circuit Interrupters (AFCI)
  • #12 awg - Yellow
  • #10 awg - Orange
  • #8 and larger - White

    Insulation Colours:
  • 2 Conductors - Black, White
  • 3 Conductors - Black, Red, White

    NMD90 is also available with a RED Jacket( commonly referred to as "HEATEX").
    This cable is designed for use on 240-volt systems where there is NO NEUTRAL.
    The cable has only a black and a red conductor in addition to the bare bonding wire.
    It should NOT be used on 110-volt systems as there is no neutral, and it is DANGEROUS to use either the red or the black conductor as a neutral.
    Large sizes are available for use with electric furnaces.

     

    For full design features, standard certifications and construction data, contact your sales Representative


    Note: All dimensions are nominal and are subject to normal manufacturing tolerance.
    Specifications are subject to change without prior notice


    • Disclaimer: Great effort was taken to ensure the accuracy of the information presented, but errors or omissions may occur. This listing of information is presented as a courtesy and does not ensure that a product with these specifications is available. Specification and availability should be confirmed with a call to your local sales office.

    Printing Instructions

    Close

    For best results in printing our product spec sheets, we request that you set your printer to Landscape Orientation.

    To proceed with printing this page, click the YES button below.